TECHNICAL CONDITION EVALUATION OF CONSTRUCTION MATERIALS OF A TURBO-REFRIGERATION UNIT PARTS OF AN AIRCRAFT AIR CONDITIONING SYSTEM BY CHANGING THE LEVEL OF RESIDUAL STRESSES

One of the frequent causes of aviation incidents and accidents is the failure of technical equipment and the destruction of aircraft (AC) constructions resulting from unacceptable deformations and structural destruction of the parts operating under high mechanical loads. Operation of parts, assemblies and units of aeronautical equipment in the most typical cases does not allow their plastic strain. Thus, in accordance with the airworthiness standards, aeronautical equipment should not be used under the conditions leading to the occurrence of dangerous permanent yielding and fatigue damage to the material in its structures. The probability of these negative factors is determined by the stress condition of the aircraft structural component material during operation. An important factor that determines the stress condition as well as the technical condition of an object of technology is residual stresses, most often available in the material of the part. In particular, the summation of the residual stresses with the stresses of the operating load can lead to the  exceedance of the critical values stress condition indicators, for example, the fatigue margin or the yield point of the material. In view of this, the development of new technologies that will provide information on the actual technical condition of the structure of each aircraft during its operation considering residual stresses is a critical task. The article describes a possible approach to evaluating and predicting the technical condition of the structural materials of assemblies and units operating under cyclic loading based on determining the change of residual stresses level on the surface of the parts during their operation. As a method for determining residual stresses, the X-ray diffractometric method was chosen, as it is characterized by high accuracy and reliability of the results obtained. The developed approach was tested on the components of the aircraft air conditioning system (turbo-refrigeration unit). The results of evaluating the technical condition of the parts conform to the facts of their operational damage. In these circumstances, although the proposed approach cannot currently be used directly on board an aircraft for continuous monitoring of the technical condition of aircraft structural materials, however, its development seems to the authors to be promising for these purposes.

aeronautical equipment, construction materials, cyclic loading, technical condition evaluation, residual stresses, X- ray diffraction method, parts of a turbo-refrigeration unit

1. Roberov, I.G., Figurovsky, D.K., Kiselev, M.A., Grama, V.S., Matveev, D.B. and Ivanov, V.O. (2020). Integrated diagnostics of technical condition and serviceability evaluation of metal materials by nondestructive testing methods. Zagotovitelnyye proizvodstva v mashinostroyenii, vol. 18, no. 4, pp. 178–181. (in Russian)

2. Figurovsky, D.K., Roberov, I.G., Grama, V.S. and Kiselev, M.A. (2018). Otsenka tekhnicheskogo sostoyaniya tonkolistovoy trip-stali posle silovogo vozdeystviya [Assessment of the technical condition of thin-sheet trip-steel after force action]. KIMILA-2018: materialy III Otraslevoy konferentsii po izmeritelnoy tekhnike i metrologii dlya issledovaniy letatelnykh apparatov [Proceedings of the III Industry Conference on Measuring Technology and Metrology for Aircraft Research]. Zhukovsky: TSAGI, pp. 239–245. (in Russian)

3. Kotelkin, A.V., Zvonkov, A.D., Lyuttsau, A.V. and Matveev, D.B. (2009). Ostatochnyye napryazheniya i portativnyye rentgenovskiye difraktometry dlia ikh opredeleniya [Residual stresses and portable X-ray diffractometers for their determination]. V kn.: Progressivnyye tekhnologii OMD [In book: Progressive technologies of OMD]. Moscow: IRIAS, pp. 423–435. (in Russian)

4. James, M.R. (1982). The relaxation of residual stresses during fatigue. Residual Stress and Stress Relaxation: Sagamore Army Materials Research Conference Proceedings, in Kula E., Weiss V. (Eds.). Springer, Boston, MA, vol. 28, pp. 297–314. DOI: 10.1007/978-1-4899-1884-0_16

5. Berkley, S.G. (1996). Method for measuring and extending the service life of fatiguelimited metal components. United States Patent US, no. 5490195A, February 02, 1996.

6. Rezende, A.B., Fonseca, S.T., Minicucci, D.J., Fernandes, F.M., Farina, P.F.S. and Mei, P.R. (2020). Residual stress characterization by x-ray diffraction and correlation with hardness in a class railroad wheel. Journal of Materials Engineering and Performance, issue 9, pр. 6223–6227. DOI: 10.1007/s11665-020-05097-x

7. Mishchenko, A., Wu, L., da Silva, V.K., Scotti, A. (2018). Analysis of residual stresses resulting from the surface preparation for X-ray diffraction measurement. Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 40, issue 2, article number: 94. DOI: 10.1007/s40430-018-1036-5

8. Luo, Q. and Yang, S. (2017). Uncertainty of the x-ray diffraction (XRD) sin2 ψ technique in measuring residual stresses of physical vapor deposition (PVD) hard coatings. Coatings, vol. 7, issue 8, ID: 128. DOI: 10.3390/coatings7080128 (accessed 10.09.2020).

9. Xu, X., Yu, H. and Lin, Z. (2020). Study of residual stress variation with depth of friction stir welded aluminium plates with different thicknesses. Science and Technology of Welding and Joining, vol. 25, iss. 4, pp. 297–302. DOI: 10.1080/13621718.2019.1693722

10. Prevéy, P.S. (1986). X-ray diffraction residual stress techniques. Metals Handbook, vol. 10, Metals Park, OH: American Society for Metals, pp. 380–392. DOI: 10.31399/asm.hb.v10.a0001761

11. Umansky, Ya.S., Skakov, Yu.A., Ivanov, A.N. and Rastorguyev, L.N. (1982). Kristallografiya, rentgenografiya i elektronnaya mikroskopiya [Crystallography, X-ray and electron microscopy]. Moscow: Metallurgiya, 632 p. (in Russian)

12. Kotelkin, A.V., Zvonkov, A.D., Lyuttsau, A.V., Matveev, D.B. and Roberov, I.G. (2012). Primeneniye metoda rentgenovskoy difraktometrii dlya otsenki sostoyaniya elementov konstruktsiy aviatsionnoy tekhniki [Application of the X-ray diffractometry method for assessing the state of structural elements of aviation equipment]. Tekhnika vozdushnogo flota, pp. 21–25. (in Russian)

13. Sosnovskiy, L.A. (1994). Mekhanika ustalostnogo razrusheniya: slovar-spravochnik [Fatigue fracture mechanics: reference dictionary], part 2. Gomel: NPO «TRIBOFATIKA», 340 p. (in Russian)

14. Sosnovskiy, L.A. (1994). Mekhanika ustalostnogo razrusheniya: slovar-spravochnik [Fatigue fracture mechanics: reference dictionary], part 1. Gomel: NPO «TRIBOFATIKA», 328 p. (in Russian)